Easy DIY Board and Batten Wall (Without Removing Baseboards) (2024)

DIY

One of my favorite ways to update a space is to add an accent wall. There are so many possibilities from beadboard to shiplap to geometric designs. In this post, we want to talk about a classic design: board and batten. This tutorial will work for a traditional board and batten design as well, but we’re going to add a little twist to it.

First, we’re doing double battens for a different take on the design. Second, we’re using ¼” wood so that the design works well with our traditional baseboards.

If you use a typical 1×2 or 1×3 for the design and have traditional baseboards, you either have to remove and replace the baseboards, add an additional trim piece to bump the baseboard out, or look at your battens severely overhang your baseboards.

By using these thinner pieces, the battens don’t stick out from the wall as much and barely overhang the baseboard. They still aren’t perfectly flush, but the amount they stick out is minimal and definitely not nearly as noticeable as it is when using thicker boards.

Easy DIY Board and Batten Wall (Without Removing Baseboards) (1)

Alright, let’s dive in and install a board and batten accent wall!

How to Create a Simple Board and Batten Wall

Recommended Tools:

Shopping List:

Our Finish:

We used Stainmaster paint in Wedding White in a satin sheen for our accent wall. The other walls are Sherwin Williams Accessible Beige

Easy DIY Board and Batten Wall (Without Removing Baseboards) (2)

STEP 1: DETERMINE THE SPACING

The first step is arguably the most difficult. You need to determine how many battens you want. We laid our boards up against the wall to help decide how many we wanted. Ultimately, we ended up with 4 sets of battens (plus one batten in each corner).

Easy DIY Board and Batten Wall (Without Removing Baseboards) (3)

Our wall was just shy of being 114” wide, so our spacing between batten pairs was about 18.5”.

Once you determine how many battens you want, you can head over to this board and batten calculator to determine the spacing between the boards.

Since we are doing double battens with a 1.5” gap between the boards, we entered our battens as being 4.5” wide. We also had to add 6” to our overall room length since the calculator puts a full batten width in each of the corners and we were only putting (1) 1.5” batten in each corner.

As you’re determining your spacing, be sure that your spacing avoids outlets or other obstacles like ethernet ports.

Easy DIY Board and Batten Wall (Without Removing Baseboards) (4)

STEP 2: CUT YOUR BOARDS

Once you determine the spacing, you need to determine the height. We cut our battens to be 59.5” tall. The main reason for this was so that we could get away with only needing one roll of the wallpaper that we placed above the board and batten wall.

For reference, the ceiling height in this room was 8’. With the baseboards and the 1×3 on top, our final height of the board and batten from the ground was 65.5”.

Cut your battens to this height. We actually ran out of full-length battens because we were originally planning on having less battens on the wall.

To fix this, we spliced together two pieces to create a single batten. To do this, you’ll cut one side of each of the two boards at a 45-degree angle and slide the angled sides on top of one another.

Easy DIY Board and Batten Wall (Without Removing Baseboards) (5)

One thing to note is that we did cut all of our boards to the same height ahead of time, but you may run into issues by doing this if your baseboards are not level all the way across.

STEP 3: INSTALL THE BATTENS

We will NOT be using any sort of glue for installation. The nails and caulk will be enough to hold on your design. If you add glue and decide to take the wall design down later, you’ll be stuck with extensive drywall repair before you are able to repaint.

The key to installation without glue is nailing at alternating angles. Instead of nailing all of your pieces straight in, you’ll nail slightly angled to the right and then to the left and then up and then down as you work your way up each board.

Easy DIY Board and Batten Wall (Without Removing Baseboards) (7)

This will “lock” your nails in so that you can’t just pull the batten straight out.

Before you start this step: a warning. Behind your walls may be plumbing or electrical or other things besides just studs. Any time you are nailing into a wall (even just to hang a picture frame), you should be aware of what’s behind your walls. There is always a chance that you might hit something that might end up needing to be repaired.

Another warning: if you are installing your board and batten on an outside corner, proceed with extra caution! We learned the hard way when installing our DIY faux brick accent wall that outside corners usually have a piece of metal on the outside. Hit that with a nail and it might “explode” out the side.

Alright, now that the warnings are out of the way, let’s get to it.

For the battens, we will be using 1” nails. Since drywall is generally ½” thick and our battens are ¼” thick, this will leave just ¼” going beyond the drywall. Most electrical wires are run between the studs about an 1” into the wall.

Start by installing your first batten in the corner. Place your batten on the baseboard and add a nail near the bottom of the batten.

Place a level on the side of the batten to ensure it’s straight. Not all walls are straight, so it’s best to use a level rather than just pushing it up against the wall. If there are gaps, you can caulk it later. Once it’s level, add a few more nails to fully secure it. We added a nail every 12-18”, but there’s no official “rule” to follow.

Easy DIY Board and Batten Wall (Without Removing Baseboards) (8)

The battens in the corners are where we pieced two boards together to get the look. You can see how the boards slide together with the angles. We’ll add wood filler to the seamless and sand off the excess to make it unnoticeable.

Easy DIY Board and Batten Wall (Without Removing Baseboards) (9)

Once your corner battens are installed, measure where you need to place the next batten and repeat the installation process of placing it on the baseboard, adding a nail to keep it in place, leveling the batten, and nailing the rest up at alternating angles.

For the double battens, we cut a small piece from one of the battens to use as a spacer. Place the spacer next to the batten you just installed and then place the second batten next to it. Nail in place.

Easy DIY Board and Batten Wall (Without Removing Baseboards) (10)

Slide the spacer up and push the second batten so that it’s flush with the spacer as you nail it in.

Once the second batten is installed, you can measure to the starting point of your next batten and repeat until your entire wall is done.

STEP 4: INSTALL THE TOP BOARD

For the top board, we used a 1×3, but you could also use a thinner board here as well if you wanted your battens and the top board to be flush.

Before installing the top board, mark the studs. Since this board spans all the way across the top, you can actually install it into the studs.

Place your top board on the battens and nail it into the studs. Since this wood was thicker, we used 1.5” nails on this board.

If your room is too long and you need to piece two boards together, you can use the same technique we discussed earlier and cut your boards at a 45-degree angle and slide them together.

Easy DIY Board and Batten Wall (Without Removing Baseboards) (11)

STEP 5: CAULK, SPACKLE, PAINT

If you want a professional looking project, you do not want to skip these finishing steps. This is what’s going to take your project from looking good enough to looking great.

Easy DIY Board and Batten Wall (Without Removing Baseboards) (12)

First, fill any nail holes and seams with spackle or wood filler. Make sure to overfill the holes and gaps. They say the wood filler/spackle doesn’t shrink, but it does shrink slightly when it dries, so you want to overfill it.

Once dry, sand off the excess. I like to close my eyes and run my fingers over the seams and areas I filled. If I can feel where there areas are, I still have more sanding to do. If it’s seamless, I’m good to go.

Once you’ve gotten everything sanded down, wipe things down so that you don’t get dust in your caulk.

Apply caulk to any area where a piece of wood meets the wall. Even if it doesn’t look like there are any gaps, add a bead of caulk for a seamless finish.

Easy DIY Board and Batten Wall (Without Removing Baseboards) (13)

Once the caulk is dry, you can paint your wall. If you opted to use non-primed boards, be sure to prime the wood first and then lightly sand before painting. Without primer, the wood grain tends to flash through in certain lighting.

There you have it! This was a small accent wall, but to install the battens themselves, we were able to get everything up in less than 10 minutes (literally). The longest part of this project is the planning and the painting.

Easy DIY Board and Batten Wall (Without Removing Baseboards) (14)

So now that you’ve seen how quickly you can make a big impact in a space, where are you going to add board and batten to your home?

Easy DIY Board and Batten Wall (Without Removing Baseboards) (2024)

FAQs

Do I need to remove baseboards for board and batten? ›

You don't have to remove your baseboards. No complicated measuring here – using my method, depending on the length of your wall, your battens will be between approximately 8-16 inches apart.

How do you cut baseboards without removing them from the wall? ›

Your first thought might be that you need to pry off the whole baseboard and cut it to size with a circular saw in your shop. However, you don't have to go through the extra effort of removing the whole thing. Use an oscillating multi-tool to get a precise cut while it's still on the wall.

What is the gap between board and batten walls? ›

It's best to space them evenly, about 10-12 inches apart, but they don't have to be exact. For example, if your wall is 100 inches wide, you'll install a 2-inch board on either side, then have 96 inches left to fill. Divide 96 by 12 (the number of inches between each batten, center to center) to get 8.

Do you have to remove baseboards? ›

Baseboards are boards installed along the lowest part of interior walls, directly next to the floor. The purpose of baseboards is to hide the joints between the wall and floor as well as add visual appeal to the space. Most flooring applications do not require you to remove existing baseboards.

Do you screw or nail board and batten? ›

Boards should be screwed 2” from both the top and the bottom and then at least every 2' vertically. Nails are not recommended for exterior wood siding! 7. It is best to install all window and door trim before installing the battens.

Why are baseboards pulling away from wall? ›

There are several reasons that a gap might be forming. Perhaps the contractors who built your home were inexperienced. Or maybe your floor joists are rotting due to excess moisture, causing your floors to sag. Baseboards that are separating from walls are also an early sign of foundation settlement.

How do you temporarily remove baseboards? ›

Slide a thin putty knife behind the molding and gently tap with a hammer to loosen it. Employ a pry bar, placing a wood block against the wall for leverage to pry the molding away without causing damage.

Do painters remove baseboards? ›

There are plenty of professional paint experts who can paint your baseboards neatly and efficiently in place. But there are some cases where it may be easier and will give you a better finish if the baseboards are removed from the wall, prepped, sanded, re-painted, then reinstalled.

Is there a special tool to remove baseboards? ›

Yes, the Trim Puller Mini can be used to remove door casings, crown molding, baseboards, and wall trim. Where can I purchase the Trim Puller Mini? The Trim Puller Mini can be purchased at Lowes.

Can you have walls without baseboards? ›

Opting to not have any baseboards will keep your design simple and modern. The only downside is a loss of protection for your walls from brooms and vacuums. That said if you don't expect too much horseplay around your house, being able to have a bookshelf flush against your wall is a real upside.

Do you have to remove baseboard for board and batten? ›

But don't want to have the expense or hassle of ripping out your existing baseboards? You can add decorative trim without an ugly overhang by using inexpensive base cap transition from your existing baseboards to your new trim.

What are the rules for board and batten? ›

apart, battens should overlap by at least 1/2 in. With wider boards, increase batten overlap proportionately. While there are no set widths for board and batten siding, an attractive combination is 1×3 battens with 1×10 boards. Siding should be nailed to horizontal blocking lines or to furring strips.

Are board and batten walls outdated? ›

Few wall treatments are more classic than traditional board-and-batten. It never goes out of style, but, as part of the current farmhouse trend, its popularity is flourishing.

Do you remove baseboards before installing wood flooring? ›

New hardwood floors can be installed with the baseboards left on, but generally, they shouldn't be. Your baseboard will look shorter and be harder to replace in the future with the new floor going up against them.

Do you need to remove baseboards to install vinyl planks? ›

Don't want to deal with removing baseboards? You can leave them in place, but you will need to leave a ¼” gap between the baseboard and flooring, to account for expansion over time. You may want to purchase some quarter-round pieces in a matching color to cover up this gap.

Do you have to remove baseboard to install beadboard? ›

The same is true for any accent wall you install such as board and batten or a fun geometric accent wall. It all comes down to preference and convenience. For the beadboard, you just slide your board snug right on top of your existing baseboard. As long as it's flush and flat it will look seamless once finished.

References

Top Articles
Latest Posts
Article information

Author: Chrissy Homenick

Last Updated:

Views: 6392

Rating: 4.3 / 5 (54 voted)

Reviews: 93% of readers found this page helpful

Author information

Name: Chrissy Homenick

Birthday: 2001-10-22

Address: 611 Kuhn Oval, Feltonbury, NY 02783-3818

Phone: +96619177651654

Job: Mining Representative

Hobby: amateur radio, Sculling, Knife making, Gardening, Watching movies, Gunsmithing, Video gaming

Introduction: My name is Chrissy Homenick, I am a tender, funny, determined, tender, glorious, fancy, enthusiastic person who loves writing and wants to share my knowledge and understanding with you.